【USA】3 Axis Mach3 CNC Controller Kit Nema23 Stepper Motor 270oz.in&TB6560 Driver

Description: 【USA Stock & Fast Shipping】【USA】3 Axis Mach3 CNC Controller Kit Nema23 Stepper Motor 270oz.in&TB6560 Driverfor CNC Router Milling Engraving Machine Good News: We have USA Warehouse in United States,so we will ship from USA Warehouse to United States. Package included: 3 x TB6560 MD430 single axis driver 3 x 23HS8430B stepper motor (dual shaft) 1 x 350W 24V/10A switching power supply 1 x 5 axis breakout board 1 x DB25 parallel cable 1 x USB cable English user manual for breakout board and stepper motor driver will send by email. I. TB6560 MD430 Low noise of stepper motor driver 1. Introduction MD430 is a compact single axis bipolar 3.0A/phase stepper motor microstepping driver with step and direction inputs, DIP switch settable step mode (full, half, eight and sixteenth--S3/S4), torque (100%, 75%, 50%, 20%--S5/S6) ,work current (0-3A--SW1/SW2/SW3) and decay mode (0%, 25%, 50% and 100%). MD430-HZ 2. Features 1) Single-chip motor driver for sinusoidal microstep control of stepping motors 2) Power on in indication led 3) 3Amps-34Volts(Supply voltages:12-34DC) 4) Full step, half step, eight step and sixteenth step(selection with dipswitches) 5) Torque (100%, 75%,50%, 20%) 6) Work Current (0-3A selection with SW1/SW2/SW3) 7) 4 Wire,6 Wire,8 Wire stepper motors can be used 8) Two phases bipolar driver 9) Easy wiring with standard screw terminals 10) Step frequency up to 100khz 11) Fuse protection on power supply rail(protects the board,but also your power supply and motor) 3. Application fields Suitable for all kinds of small and medium-sized automation equipment and apparatus For example, laser machines, laser engraving &cutting machine, laser subsurface engraving machine, laser handicraft cutting machine, (nonmetal materials) laser marking machine, laser seals engraving machine and photosensitive seal machine. II. 5 axis CNC Breakout board interface adapter board Description: 1, full support for MACH3, KCAM4, EMC2, the PC software to support parallel port control; 2, leads to all the parallel port of all 12 data transmission output pin, which can control the five stepper motor driver; 3, with 5-way input interface, you can access the limit switches and emergency stop switch, reset knife;5 input LED indicates the status of the input; 4, all the way with a 12A relay control, normally open, normally closed leads, user-friendly connection; 5, power supply with 5V USB power supply or external power supply to facilitate the access of external power supply;On the external drive enable signal amplification, filtering, enhancement processing; 6, the pulse, the direction of signal shaping, enhanced with a carrying capacity, data transmission speeds reach 10 MBit / S; 7, the output pin with extension interfaces can 2.54mm pin 2.54mmXH-Block; Superiority: 1,the use of new imported Japanese Toshiba TB6560 chip (disguising); 2,The base used dense teeth radiator, cooling super, to ensure the stable operation of equipment; 3,the input signal using a high-speed opto-isolation to ensure not losing steps, which the pulse direction signals with the same level of 6N137, dual high-speed optocoupler; 4 a variety of semi-flow mode and the semi-flow current selection, the use of more flexible 5,Decay mode is adjustable to ensure the motor running smooth; 6.,Sophisticated appearance size cooling pad size: 75mm * 65mm, four mechanical installation positioning hole size is: 67mm * 58, mounting hole diameter is 4mm 7,Set method detailed table on the board, easy to use; 8,With anti-reverse circuit, even if not careful the power plug back and will not burn the chip, the use of safer. III. Stepper Motor General Specification: Step angle accuracy:+ - 5%(full step,not load) Resistance accuracy: + - 10% Inductance accuracy:+ - 20% Temperature rise: 80deg Max(rated current,2 phase on) Ambient temperature ----------—20deg ---- +50deg Insulation resistance:100ohm Min,500VDC Insultion Strength--------500VAC for one minute Datasheet (23HS8430B,front shaft is 8mm diameter shaft,21mm lenth,back shaft is 6.35mm dia and 10mm length,270oz-in or 18kg.cm holding torque) Note:if you need double shaft pls contact us,we can produce. Motor lead wires: RED: A+ GREEN: A- YELLOW: B+ BLUE: B- IV.Switching power supply 350W,Input:100-120VAC or 200-240VAC,50/60Hz,Output:24v/14.5 A,single output switching power supply PaymentWe accept payment through PAYPAL only. Shipping 1.Items will be shipped within 1-2 days upon the receipt of payment.2.Please check out your address carefully when processing order.We are not responsible for wrong or undeliverable address.We will ship item to your PAYPAL address. If other address, please advise us by eBay or E-mail.3.The estimated delivery time is 7~15 workings days to Asian, USA, AU, UK and most western European countries;15~30 workings days to most other countries. Return&Refund 1.Any reason required for all refund.Item must be in it's original condition and no physical damage,buyer responsible for all shipping cost.2.When you have the parcel,and not satisfied the goods or it is other problem like as broken,pls tell us the detail reason and provide the photos,we will help you to solve any problems. Contact 1.If you are not satisfied, please contact us to resolve any issues. Please do NOT leave negative feedback without asking for help. We work hard to make sure EVERY CUSTOMER 100% satisfaction.2.For any inquiries,issues or assistanceplease contact us via eBay or leave your mail address.3.All emails will be answered within 1-2 working days.If you do not receive our reply,please kindly re-send your email and we will reply to you as soon as possible.

Price: 133 USD

Location: New York

End Time: 2024-08-16T08:24:13.000Z

Shipping Cost: 0 USD