New Prestige 105BP Keyless Starter Remote ELVATJA + Programming Instructions

Description: New Prestige 105BP Keyless Starter Remote ELVATJA + Programming Instructions New Prestige 105BP Keyless Starter Remote ELVATJA + Programming Instructions Battery IncludedFree Tech SupportGuaranteed To WorkTested Before Shipping New Prestige 105BP Keyless Starter Remote ELVATJA with programming instructions and battery included free. Works on these Audiovox / Prestige / Pursuit systems: APS25C, APS422E, APS510C, APS57C, APS57CA, APS596C, APS687C, APS787C, APS901C, APS922E, APS997C, PRO9051E, PRO9051i, PRO9056C, PRO9056i, PRO9276C, PRO9276i, PRO9276TW, PRO9556C, PRO9556CA, PRO9556i, PRO9644C, PRO9644i, RO9776C, PRO9776i, PRO9801C and PRO9801i. PROGRAMMING PROCEDURE: 1) Enter the vehicle, and turn the ignition switch to the on position. 2) Press and release the valet push-button switch three times. NOTE: Some systems may use a combination push-button LED switch. In these systems the push-button and the dashmounted LED are one and the same. 3) The dash mounted LED will flash 1x, and the siren will chirp 1x, indicating that the system is ready to accept programming of channel #1 which is arm/lock, disarm/unlock/unlock 2, and panic functions. 4) Press and hold the lock or lock/unlock symbol button of the transmit- ter you wish to program for 4 seconds or until a long chirp is heard from the siren. "Repeat step 4 for each transmitter you wish to program". NOTE: If your transmitter button has the Lock/Unlock icon on one button, press and release the valet push button switch 2 times then move on to step #8. 5) Press and release the valet push button switch one time to advance to channel 2. The siren will chirp 2 times and the dash-mounted LED will Flash 2 times, indicating that the unit is ready to accept programming for channel # 2 which is only used for separate lock and unlock button transmitters, and is the disarm/unlock/unlock 2 and panic. 6) Press and hold the unlock symbol button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren. "Repeat step 6 for each transmitter you wish to program". 7) Press and release the valet push button switch one time to advance to channel 3. The siren will chirp 3 times and the dash-mounted LED will Flash 3 times, indicating that the unit is ready to accept programming for channel # 3 which is the trunk release/alternate output channel of the system. 8) Press and hold the trunk/key symbol button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren. "Repeat step 8 for each transmitter you wish to program". 9) Press and release the valet push button switch one time to advance to channel 4 if so equipped. The siren will chirp 4 times and the dash mounted LED will Flash 4 times, indicating that the unit is ready to accept programming for channel # 4, optional device (where equipped) 10) Press and hold the Option button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren. "Repeat step 10 for each transmitter you wish to program". 11) Press and release the valet push button switch one time to advance to channel 5 if so equipped. The siren will chirp 5 times and the dash mounted LED will Flash 5 times, indicating that the unit is ready to accept programming for channel # 5 optional device (where equipped) 12) Press and hold the second Option button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren. "Repeat step 12 for each transmitter you wish to program". 13) Within 10 seconds, press and release the valet program switch one time. (Siren emits 6 short chirps indicating channel 6 has been entered) 14) Within 10 seconds, Press and hold the unlock button, (or any unused button(s)), of the first transmitter you wish to control Channel 6 output, (Driver Priority 1) until a long chirp is heard from the siren. (Repeat this for each transmitter you wish to operate the Channel 6 output, Driver Priority 1) 15) Within 10 seconds, press and release the valet program switch one time. (Siren emits 7 short chirps indicating channel 7 has been entered) 16) Within 10 seconds, Press and hold the unlock button (or any unused button(s)) of the first transmitter you wish to control Channel 7 output, (Driver Priority 2) until a long chirp is heard from the siren. (Repeat this for each transmitter you wish to operate the Channel 7 output, Driver Priority 2) NOTE: Channels 6 and 7 can be used as a separate output to control a function other than driver priority. Simply programming any unused transmitter button other than the unlock button will allow complete independent control of these outputs. BATTERY REPLACEMENT: The transmitter incorporates a small LED visible through the case which is used to indicate battery condition. You will notice a decrease in transmitter range as the battery condition deteriorates. Transmitter battery replacement is recommended at least every 10 to 12 months, depending upon how frequently the transmitter is used. To replace the battery: 1) Remove the 3 small # 0 Phillips head screws from the rear of the case. 2) Remove the rear cover to access the discharged battery paying attention to the proper polarity orientation. 3) Carefully remove and properly dispose of the discharged battery. 4) Insert the new battery with the + side up toward the battery clip. Reassemble the case, then reinstall the 3 small case screw removed in step 1. 5) If you accidently dislodge the circuit board from the transmitter hous- ing, be certain that the rubber membrane is seated properly, and the buttons are properly exposed from the front view of the case, then insert the circuit board, and return to step #4. This Transmitter uses CR2032 Coin Cell Type Batteries. After removing the three #0 point phillips screws shown pry apart case with the edge of a finger nail or a small common screwdriver. Keep hold of the metal key ring loop to prevent it's loss as it will separate from the transmitter case. Carefully remove the discharged battery by sliding it out from under the clip in the direction indicated by the arrow in the diagram below. Properly dispose of the discharged battery and insert a new CR2032 taking care to arrange it so that the + is facing up toward the + symbol on the battery clip. Reassemble in the reverse of above. Brand: Audiovox Warranty: 6 months SKU: Z3223A Manufacturer Part Number: 105BP InternalID: 93 Product Type: Regular Remote Code Type: Hopping Remote Programming: Onboard Buttons: 5 Frequency: 302 MHz RF Transmission: 1Way Manufacturer: Genuine Family Name: Audiovox Type 9 Product Character: System Specific Fast shippingSame-day handling! Choose from multiple USPS and UPS shipping methods.Satisfaction Guaranteed 30-day no-hassle returns and exchanges.Top-notch Support Our agents can walk you through programming and troubleshooting.Security and Privacy We use SSL security to protect your data. We won't ever sell your data. We ship every day Monday - Friday. We hope you will love your purchase, however if you need to return it, we have a 30 day return policy.

Price: 59.95 USD

Location: Brooklyn, New York

End Time: 2024-08-25T14:34:31.000Z

Shipping Cost: N/A USD