Basler acA1300-30gc Industrial Camera USED Fanuc iRVision ready camera

Description: General Specifications SpecificationacA1300-30gcResolution (H x V Pixels) 1294 x 964 Sensor TypeSony ICX445AQProgressive scan CCD Global shutterOptical Size1/3"Effective Sensor Diagonal 6.1 mmPixel Size (H x V)3.75 μm x 3.75 μmFrame Rate (at Default Settings) 30 fpsProduct Line ace classicMono / ColorColorImage Data InterfaceFast Ethernet (100 Mbit/s) Gigabit Ethernet (1000 Mbit/s)Pixel FormatsSee Pixel Format. SynchronizationVia hardware trigger Via software trigger Via free runExposure Time ControlVia hardware trigger Programmable via the camera API Camera Power RequirementsPower over Ethernet (PoE) 802.3af compliant supplied via Ethernet connector12 VDC supplied via I/O connector≈2.7 W when using Power over Ethernet≈2.2 W @ 12 VDC when supplied via I/O connectorI/O Lines1 opto-coupled input line 1 opto-coupled output line Lens MountC-mount, CS-mount Size (L x W x H)42.0 mm x 29 mm x 29 mm (without lens mount or connectors)60.3 mm x 29 mm x 29 mm (with lens mount and connectors)Weight<90 g ConformityCE (includes RoHS), UL Listed, FCC, GenICam, GigE Vision, IP30, IEEE 802.3af (PoE), REACHThe EU Declaration of Conformity is available on the Basler website Software Basler pylon Camera Software Suite (version 4.0 or higher) Available for Windows, Linux x86, Linux ARM, and OS X Accessories Cables for your camera model Lenses for your camera model Additional accessories for your camera model Spectral Response The spectral response curve excludes lens characteristics, light source characteristics, and IR cut filter characteristics. IR Cut FilterColor cameras are equipped with an IR cut filter. The filter is mounted in a filter holder inside the lens mount.The IR cut filter has the following spectral characteristics: Wavelength [nm]Transmittance450–610Tmin > 90 %450–620Tavg > 93 %645 ± 10T = 50 %700–1070Tmax < 4 %690–1070Tavg < 1 % The filter holder can be removed. For more information, see the ace IR Cut Filter Holder Removal Procedure application note. Mechanical Specifications Camera Dimensions and Mounting Points C-Mount Camera Models CS-Mount Camera Models Maximum Allowed Lens Intrusion→ See Maximum Allowed Lens Intrusion. Stress Test Results→ See Stress Test Results. Requirements Environmental Requirements Temperature and Humidity Housing temperature during operation0–50 °C (32–122 °F)Humidity during operation20–80 %, relative, non-condensingStorage temperature-20–80 °C (-4–176 °F)Storage humidity20–80 %, relative, non-condensingHousing temperature according to UL 60950-1max. 70 °C (158 °F)Ambient temperature according to UL 60950-1max. 30 °C (86 °F) Heat Dissipation→ See Providing Heat Dissipation. Electrical Requirements Camera Power Power supply via Power over Ethernet (PoE): Power must comply with the IEEE 802.3af specification.Power supply via I/O connector: The nominal operating voltage is 12 VDC (10.8 VDC minimum, 13.2 VDC maximum), includes <1 % ripple. Opto-Coupled I/O Input Line Voltage Description30 VDCAbsolute maximum. This voltage must never be exceeded. Doing so may damage the camera and voids the warranty.0–24 VDCSafe operating range.0–1.4 VDCIndicates a logical 0 (with inverter disabled).>1.4–2.2 VDCRegion where the logic level transition occurs; the logical state is not defined in this region.>2.2 VDCIndicates a logical 1 (with inverter disabled). Opto-Coupled I/O Output Line Voltage Description30 VDCAbsolute maximum. This voltage must never be exceeded. Doing so may damage the camera and voids the warranty.3.3–24 VDCSafe operating range.<3.3 VDCUnreliable I/O output.Leakage current: <60 µA. Actual leakage depends on operating temperature and production spread of electronic components.Maximum load current: 50 mAMinimum load current: Not specified. However, consider the following: Leakage current will have a stronger effect when load currents are low. Propagation delay of the output increases as load currents decrease. Higher-impedance circuits tend to be more susceptible to EMI.Higher currents cause higher voltage drops in long cables. Circuit Diagrams→ See Circuit Diagrams for Basler ace Cameras. Cable Requirements Ethernet CableUse a high-quality Ethernet cable. Use of shielded CAT 5E or better cables with S/STP shielding is recommended.Use either a straight-through (patch) or a cross-over Ethernet cable.As a general rule, applications with longer cables or applications in harsh EMI conditions require higher category cables.Close proximity to strong magnetic fields should be avoided.Basler recommends using Ethernet cables from the Basler Vision Components range. I/O CableThe I/O cable must be shielded. The I/O cable must have a cross-section of at least 0.14 mm² (close to AWG26). Use a twisted pair wire cable.Maximum recommended cable length: 10 mCamera-side connector: Hirose micro plug (part number HR10A-7P-6S) or equivalentClose proximity to strong magnetic fields should be avoided.If you are supplying power to the camera via Power over Ethernet, the I/O cable will not be used to supply power. However, you can still use the cable to connect to the I/O lines.Basler recommends using I/O cables from the Basler Vision Components range: Opto-I/O cable, 10 m (blue cable): For use with the opto-coupled I/O lines of your camera. Does not provide camera power. Therefore, when using this cable, you must provide power via Power over Ethernet (PoE). Power-I/O cable, 10 m (gray cable): For use with the opto-coupled I/O lines of your camera. Unlike the opto-I/O cable (blue cable, see above), this cable provides camera power. Opto-GPIO Y-cable, 2 x 10 m (yellow-blue cable): Offers two separate wires.One can be used to connect the opto-coupled I/O lines of your camera. The other one can be used to provide camera power. Power-I/O PLC+ cable, 10 m (gray cable): For use with the opto-coupled I/O lines of Basler cameras connected to a programmable logic controller ( PLC). It adapts the signal level for zero voltage from PLC level (<8.4 VDC) to TTL level (<1.4 VDC). Physical Interface Camera Connectors Connector DescriptionEthernet connector100/1000 Mbit/s Ethernet connection to the cameraIf power is not supplied via I/O connector: Power over Ethernet (PoE) 8-pin RJ-45 jack Recommended mating connector: 8-pin RJ-45 plug (snap-in or with locking screws). When using locking screws, note the horizontal orientation of the screws. I/O ConnectorIf power is not supplied via Power over Ethernet (PoE): Power supplyHirose micro receptacle (part number HR10A-7R-6PB) Recommended mating connector: Hirose micro plug (part number HR10A-7P-6S) Connector Pin Numbering and Assignments PinLineFunction1-12 VDC camera power2Line 1Opto-coupled I/O input line3-Not connected4Out 1Opto-coupled I/O output line5-Ground for opto-coupled I/O lines6-Ground for camera power Precautions→ See Safety Instructions for Basler ace Cameras. Installation→ See Camera Installation. Features→ See the camera features section. Suggestions for improving the documentation? Send us your feedback on this topic.For technical questions, please contact your local distributor or use the support form on the Basler website.

Price: 149.95 USD

Location: Fremont, California

End Time: 2024-08-23T19:05:35.000Z

Shipping Cost: 9.95 USD