AEM V3 Water/Methanol HD Controller Kit - Internal MAP with 40psi max #30-3306

Description: Not for sale or street use in CA & CARB states.AEM's Boost Dependent HD turbo Diesel Controller has an on-board MAP sensor (up to 40 PSI) with a molded in nipple for a boost hose pickup. The controller design features large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness's positive-lock connector. The Boost Dependent controller housing includes a wiring legend on the back, easy to access integrated fuse and molded mounting tabs.AEM's engineers spent extensive time developing the controller's flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine's need for water/methanol injection, which further optimizes charge air cooling and EGT reduction on turbo Diesels.AEM's V3 Water/Methanol Injection wiring harness for the Boost Dependent HD turbo Diesel controller is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive.AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component.All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems.Methanol is a toxic and highly flammable chemical. 100% Methanol ignites easily and burns vigorously with an almost undetectable flame. Methanol can be absorbed through the skin and even small amounts can cause blindness or even death. Using this fluid at high pressures, without dilution, in an under-hood environment with nylon lines and push-to-connect fittings is very unsafe. The performance advantages of using greater than 50% methanol concentrations are small, if they exist at all. However, the safety issues are very real and far outweigh any perceived benefit of running high concentrations of methanol.WARNING!Improper installation and/or adjustment of this product can result in major engine/vehicle damage. For technical assistance visit our dealer locator to find a professional installer/tuner near you.Note: AEM holds no responsibility for any engine damage or personal injury that results from the misuse of this product, including but not limited to injury or death caused by the mishandling of methanol. AEM V3 Water/Methanol HD Controller Kit - Internal MAP with 40psi max #30-3306 Not for sale or street use in CA & CARB states.AEM's Boost Dependent HD turbo Diesel Controller has an on-board MAP sensor (up to 40 PSI) with a molded in nipple for a boost hose pickup. The controller design features large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness's positive-lock connector. The Boost Dependent controller housing includes a wiring legend on the back, easy to access integrated fuse and molded mounting tabs.AEM's engineers spent extensive time developing the controller's flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine's need for water/methanol injection, which further optimizes charge air cooling and EGT reduction on turbo Diesels.AEM's V3 Water/Methanol Injection wiring harness for the Boost Dependent HD turbo Diesel controller is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive.AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component.All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems.Methanol is a toxic and highly flammable chemical. 100% Methanol ignites easily and burns vigorously with an almost undetectable flame. Methanol can be absorbed through the skin and even small amounts can cause blindness or even death. Using this fluid at high pressures, without dilution, in an under-hood environment with nylon lines and push-to-connect fittings is very unsafe. The performance advantages of using greater than 50% methanol concentrations are small, if they exist at all. However, the safety issues are very real and far outweigh any perceived benefit of running high concentrations of methanol.WARNING!Improper installation and/or adjustment of this product can result in major engine/vehicle damage. For technical assistance visit our dealer locator to find a professional installer/tuner near you.Note: AEM holds no responsibility for any engine damage or personal injury that results from the misuse of this product, including but not limited to injury or death caused by the mishandling of methanol. Not for sale or street use in CA & CARB states. AEM's Boost Dependent HD turbo Diesel Controller has an on-board MAP sensor (up to 40 PSI) with a molded in nipple for a boost hose pickup. The controller design features large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness's positive-lock connector. The Boost Dependent controller housing includes a wiring legend on the back, easy to access integrated fuse and molded mounting tabs. AEM's engineers spent extensive time developing the controller's flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine's need for water/methanol injection, which further optimizes charge air cooling and EGT reduction on turbo Diesels. AEM's V3 Water/Methanol Injection wiring harness for the Boost Dependent HD turbo Diesel controller is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive. AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component. All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems. Methanol is a toxic and highly flammable chemical. 100% Methanol ignites easily and burns vigorously with an almost undetectable flame. Methanol can be absorbed through the skin and even small amounts can cause blindness or even death. Using this fluid at high pressures, without dilution, in an under-hood environment with nylon lines and push-to-connect fittings is very unsafe. The performance advantages of using greater than 50% methanol concentrations are small, if they exist at all. However, the safety issues are very real and far outweigh any perceived benefit of running high concentrations of methanol. WARNING! Improper installation and/or adjustment of this product can result in major engine/vehicle damage. For technical assistance visit our dealer locator to find a professional installer/tuner near you. Note: AEM holds no responsibility for any engine damage or personal injury that results from the misuse of this product, including but not limited to injury or death caused by the mishandling of methanol. AEM V3 Water/Methanol HD Controller Kit - Internal MAP with 40psi max #30-3306 Item Description Not for sale or street use in CA & CARB states.AEM's Boost Dependent HD turbo Diesel Controller has an on-board MAP sensor (up to 40 PSI) with a molded in nipple for a boost hose pickup. The controller design features large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness's positive-lock connector. The Boost Dependent controller housing includes a wiring legend on the back, easy to access integrated fuse and molded mounting tabs.AEM's engineers spent extensive time developing the controller's flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine's need for water/methanol injection, which further optimizes charge air cooling and EGT reduction on turbo Diesels.AEM's V3 Water/Methanol Injection wiring harness for the Boost Dependent HD turbo Diesel controller is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive.AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component.All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems.Methanol is a toxic and highly flammable chemical. 100% Methanol ignites easily and burns vigorously with an almost undetectable flame. Methanol can be absorbed through the skin and even small amounts can cause blindness or even death. Using this fluid at high pressures, without dilution, in an under-hood environment with nylon lines and push-to-connect fittings is very unsafe. The performance advantages of using greater than 50% methanol concentrations are small, if they exist at all. However, the safety issues are very real and far outweigh any perceived benefit of running high concentrations of methanol.WARNING!Improper installation and/or adjustment of this product can result in major engine/vehicle damage. For technical assistance visit our dealer locator to find a professional installer/tuner near you.Note: AEM holds no responsibility for any engine damage or personal injury that results from the misuse of this product, including but not limited to injury or death caused by the mishandling of methanol. Not for sale or street use in CA & CARB states. AEM's Boost Dependent HD turbo Diesel Controller has an on-board MAP sensor (up to 40 PSI) with a molded in nipple for a boost hose pickup. The controller design features large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness's positive-lock connector. The Boost Dependent controller housing includes a wiring legend on the back, easy to access integrated fuse and molded mounting tabs. AEM's engineers spent extensive time developing the controller's flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine's need for water/methanol injection, which further optimizes charge air cooling and EGT reduction on turbo Diesels. AEM's V3 Water/Methanol Injection wiring harness for the Boost Dependent HD turbo Diesel controller is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive. AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component. All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems. Methanol is a toxic and highly flammable chemical. 100% Methanol ignites easily and burns vigorously with an almost undetectable flame. Methanol can be absorbed through the skin and even small amounts can cause blindness or even death. Using this fluid at high pressures, without dilution, in an under-hood environment with nylon lines and push-to-connect fittings is very unsafe. The performance advantages of using greater than 50% methanol concentrations are small, if they exist at all. However, the safety issues are very real and far outweigh any perceived benefit of running high concentrations of methanol. WARNING! Improper installation and/or adjustment of this product can result in major engine/vehicle damage. For technical assistance visit our dealer locator to find a professional installer/tuner near you. Note: AEM holds no responsibility for any engine damage or personal injury that results from the misuse of this product, including but not limited to injury or death caused by the mishandling of methanol. Shipping We ship Monday-Friday and strive for orders to ship within 1-2 business days. We use UPS and FedEx for the majority of our orders but reserve the right to use alternative but comparable means to get you your product as quickly and efficiently as possible. All orders will require a physical address, please provide this upon ordering to expedite the shipping process. Even with our huge inventory, we may run out of an item. If this is the case you will receive an email with an expected availability date. Returns & Warranty We offer 30 Day Free Returns. Refunds for returns will be given once the item has been received and inspected. Items must be New, Unused, Not Installed, in the Original Packaging and able to be resold. Incomplete returns may not be eligible for this policy. Please message us to start a return. Warranty on product is replacement of part only for defects in materials and workmanship. No cash or compensation for labor will be given for defects in material and workmanship. Defective part must be returned in order for new part to be provided. OUR COMMITMENT We are committed to making sure that you leave this transaction satisfied. We value your feedback, and we strive to do everything we can to earn Five Stars and Positive Feedback on every order. If you are unhappy with your purchase for any reason, please CONTACT US prior to leaving feedback so that we can make things right for you. Contact Us We encourage our Buyers to communicate with us at any time. Feel free to contact us directly through eBay. All emails will be responded to within 24 hours. We look forward to hearing from you! Powered By 3Dsellers.com - Try for Free!

Price: 196.95 USD

Location: Memphis, Tennessee

End Time: 2024-08-10T07:28:30.000Z

Shipping Cost: 0 USD