2- 4 gal Latex ROOFING Bonding Glue Adhesive

Description: Lottes Roofing St. Charles, MO 63303 "Over 30 years experience in single ply flat roofing products!" These are 2 - 4 gal pails of Latex bonding adhesive 100 lbs and is Class C-60 Not recommended to be used in temperatures lower than 50*. Temperature needs to be above 50* for 24 hours for full cure. FREE DELIVERY IN 48 states!! Check out my other items! This is latex bonding adhesive to adhere the EPDM or TPO rubber to the roofing insulation or substrate. This is a BONDING Adhesive to adhere or bond the EPDM or TPO to a substrate of wood, plywood, OSB or metal. This is NOT a seaming product that will seam EPDM to EPDM or TPO to TPO, you must use a SEAMING product like black seaming adhesive or vulcanizing seaming tape which we have available for that type of application. This is a latex based single surface bonding adhesive with coverage about 400 square feet per pail on a SINGLE surface. This adhesive is a SINGLE surface laminate adhesive that is NOT to be used in a WET condition. Allow the adhesive time to "Tack" off, which usually about 5 minutes or so. DO NOT ALLOW the adhesive to become dry before you lay in the roofing membrane. APPLY roofing membrane while the adhesive is NOT DRY BUT TACKY. Trowel application is the recommended application as per the instructions as a ONE surface WET LAMINATE. However, if you wish to use a paint roller, we recommend using a 9" fine nap paint approved roller. If you use the roller, and not a trowel, you need to put the adhesive on BOTH surfaces and let TACK dry for 5 minutes or so, like a 2 sided solvent contact adhesive, depending on weather and heat conditions. Using this application method may require the use of more adhesive than the single sided process.Then, put the 2 pieces together. Full cure normally occurs after 24-48 hours. So 2 - 4 gal pails will cover about 700-800 square feet of finished roof area.Method of Applying EPDM with heavy bodied latex bonding adhesive and 3” seam tape application as required.· 1 Clean the roof surface of all shingle debris and nails. Re-fasten any loose roof boards.· 2 Fill any gaps larger than 3/8” inch with wooden strips. The EPDM cannot span gaps of more than 3/8" without risk of possible adhesion issues.· 3 Start at the bottom of the roof and roll out the EPDM from one side of the roof to the other and let it sit for 10-15 minutes. Fold bottom half of the membrane onto the top half of the in place membrane· 4 Apply the bonding adhesive to the exposed roof deck and NOT to the EPDM membrane as the adhesive is to be applied as a one surface WET LAMINATE using a notched trowel to spread the adhesive in a pattern over the decking. Allow the adhesive a few minutes to "tack off" Slowly fold the EPDM roofing membrane back into place while the adhesive is still wet. To ensure adhesive transfer and a good bond, use a stiff bristled push broom and force the membrane into contact with the adhesive on the roof deck. Repeat the process on the other half of the EPDM membrane.· 5 Roll out the next piece of membrane, allowing a four to six inch overlap on the piece below it. This overlap is crucial to allow enough overlap between the two pieces and to allow the water to flow from the upper part of the roof down to the roof edge. This is also to allow enough room to apply the primer and 3”seam tape if required to splice 2 pieces of EPDM deck sheet together.· 6 Adhere this section in the same manner as the first section. Continue adding sections until you have covered your roof.Seam tape application if required to join 2 sheets together•Position sheets of liner and align edges to required overlap. Mark bottom sheet to indicate top sheet location, then folding back top sheet. •Clean and/or prime the seam area of both rubber sheets using FastSeam EPDM Liner Primer. CAUTION: wear protective gloves and read all labels and instructions when using EPDM Liner Primer or unleaded gas to clean and prime the seam area•Make guide marks for the splice tape much as in Step 1, except that the new marks will be 1/2" out from the edges of the bottom sheet. •Fold back top sheet. Begin unrolling splice tape by aligning the edge of the paper with the marks in step 3. Continue along the full length of the seam. •With the paper backing still attached to the tape, use a roller to ensure good contact. Place the top sheet of rubber back over the applied tape. •Remove the paper backing by pulling out from under the top sheet at a 45ºangle. Allow top sheet to fall freely onto exposed splice tape. Roll entire seam with roller. Summary of My Selling Policies Payment All Credit Cards, Company Certified Checks, Bank Checks, Money Orders, Bank Wire, Paypal Fees No sales taxes UNLESS in specific states locals Shipping US and International Delivery 24-48 hours to ship the liner NORMALLY on in stock items, not counting weekends or holidays Refunds & Returns Returns accepted on qualified items with RGA return number Contact Me BID WITH CONFIDENCE On Apr-28-08 at 11:12:31 PDT, seller added the following information: Please be prepared to unload the product from the delivery vehicle. Items less than 150 lbs will be shipped UPS or Fed Ex and will deliver directly to your door. Orders over 150 lbs delivered by Trucking Companies DO NOT DO DOOR delivery for residential delivery. It is the responsibility of the CUSTOMER to remove his product FROM or OFF the actual truck. We do NOT offer a lift gate option, that would be an expense item negotiated between the Freight Company and the customer/consignee. If you are unable or unwilling to receive your order via normal delivery according to ICC policies and truck line delivery schedules, then you will be solely responsible for all delivery charges related to attempted delivery and return freight charges. A 15% restocking fee will apply to returned items.

Price: 482.13 USD

Location: Saint Charles, Missouri

End Time: 2024-08-30T16:57:43.000Z

Shipping Cost: 0 USD