120V/480V 1,2,3 Phase electric kWh meter pulse, RS485 Internal CT + enclosure

Description: Combo package includes Meter and Enclosure with mounting plate and Din - rail Smart KWh Energy meter. With RS485 modbus RTU and pulse output. Quantity discounts available. One, Two, or Three phase, up to 4 wires. 1 Phase two wires (Line & Neutral) 2 Phase 3 wires (2 Lines & Neutral) 3 Phase 4 wires (3 lines & Neutral) Internal CTs - 100 Amps. For 3 Phase 3 Wires, no Neutral, Ground can be used as Neutral, Needed to power up the meter. Max Phase to Neutral 400 Volts. Max. Phase to Phase 480 Volts. Smart Electronic DIN-RAIL Active energy meter for marinas, campgrounds, solar panels, condominiums, tenant buildings, rental apartments, etc. Submetering applications. When connected to a pulse readers or to a computer system using RS485 standard modbus RTU it provides a key component for sub-metering electricity usage in marinas, RV parks or multi-tenant buildings. For our submetering turn key solutions, please visit beyondtech com This meter can provide a powerful start point for a wired or wireless Automatic Meter Reader System - AMR - Electricity Monitoring System. Model BEYDTS5188 one to three phase, up to four wires electronic DIN rail active energy meter with a new design, is built with high quality micro-electronics, and integrated circuit, it uses advanced digital and SMT techniques. The meter complies with relevant technical requirements of class 1 three phase active energy meter stipulated in the international standard IEC 62053-21. It can measure 50Hz or 60Hz active energy consumption accurately from one or three phase, up to four wires AC electricity net. This meter has seven digits, the LCD display shows the active energy consumption. The meter also has far infrared and RS485 communication modules in it, allowing communication with many AMR systems and pulse readers. It can connect via wires (twisted pair) or wireless Reliable, small size, elegant presentation, light weight, convenient installation, etc. Specs: •35mm standard DIN rail installation , complying with standard DIN EN50022. Front board installed (mounting holes center distance 63 mm), users can choose any one by themselves. •Ten pole width (Modulus 12.5mm), complying with standard JB/T7121-1993. •Type S wiring (Inlet from bottom, outlet from top), Allows external Current Transformers. connect operation, may select set 27 CT rate to convert power reading accurately. After the meter is setup, it will read directly from the power source or from the CTs. If reading from the CTs, it will adjust from the preset rate. •Seven digits display LCD, 5+2 digits display (99999.91 kWh, only ratio of CT when 5:5 A) •Output via polarity and non polarity ports of passive pulse. for distant, the output rate is 10 kWh/pulse, complying with standard IEC 62053-31 and DIN 43864. •Standard configuration with a port of far infrared data communication and a port of RS485 data communication. Communication complying with standard DL/T645-1997, It is possible to manufacture this meter without the data communication function with customer's request. •Six LED instructions respective in every power supply state, signal of closed energy impulse and distant energy impulse and data communication state. •Automatic detection of the direction of the flow of current load. Instructions shown on the LCD. •Single direction three components measure three phase, four wire active energy consumption. verifying the flow of the load current. Complying with standard IEC 62053-21. •Standard configuration short terminals cover, may select extension terminals cover, in order to protect to use safety. (Product Configuration code is AF). Technical Parameters: Accuracy: Class 1 Reference Voltage(V): Up to 400 V Phase to Neutral. Up to 480 V. Phase to Phase. Current specifications(A): CT/5A Starting current(A): 0.01 Insulation performance: AC voltage 4kv for 1 minute, 1.2/50us waveform impulse voltage 6kv

Price: 125 USD

Location: Miami Beach, Florida

End Time: 2024-08-25T21:32:37.000Z

Shipping Cost: 18.4 USD